再开一个——>路由器配置基础！
现在进入初始化配置以后，我配了eth0/0和eth0/1的ip,资料上所说的方法设置后，可以通过PC ping通eth0/0(eth0/1)了。
然后，我用命令write（或者用copy run start都一样，是吗？），保存running-config到startup-config中，按理说，router重启后，仍然会ping通的，是不是？可是结果不行。请大家注意，reload后，又要我进入初始化配置，是不是startup-config根本就没起作用？
信息提示如下：
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: n
Press RETURN to get started!
00:00:12: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:12: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up
00:00:12: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
00:00:12: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s
tate to up
00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed s
tate to up
00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta
te to down
00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed sta
te to down
00:00:40: %LINK-5-CHANGED: Interface Ethernet0/0, changed state to administrativ
ely down
00:00:40: %LINK-5-CHANGED: Interface Serial0/0, changed state to administrativel
y down
00:00:40: %LINK-5-CHANGED: Interface Ethernet0/1, changed state to administrativ
ely down
00:00:40: %LINK-5-CHANGED: Interface Serial0/1, changed state to administrativel
y down
00:00:40: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(1), RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Fri 27-Apr-01 11:03 by cmong
00:00:41: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s
tate to down
00:00:41: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed s
tate to down
Router>en
Router#
看，eth0/0和eth0/1的状态又变成了down了 ：（
问题点数：100、回复次数：6Top
1 楼lshdf（冷雨）回复于 2002-03-19 12:13:24 得分 10
收藏！Top
2 楼fire99（见龙在田）回复于 2002-03-19 13:20:51 得分 20
show config看一下，是否将配置好的内容写进去了Top
3 楼smart_boy1（阿德）回复于 2002-03-19 14:12:42 得分 0
当然写进去了，而且write了以后，running-config和startup-config一样了Top
4 楼webtt（tt）回复于 2002-03-19 14:33:56 得分 35
能把show int e0和show int e1的状态贴出来吗？Top
5 楼htb（htb）回复于 2002-03-19 16:08:15 得分 35
e0/0 e0/1 是你划分的子网,还是你路由器是E0是个集成HUB.如果是这样,你的E0 口只能配一个IP.我建议你还是把show int e0和show int e1的状态贴出来Top
6 楼smart_boy1（阿德）回复于 2002-03-19 21:10:19 得分 0
呵呵，谢谢大家，已搞定，是寄存器值变了——我的猜测正确Top
