路由器恢复的菜鸟问题（在线等）
YNT-C36-JC1A#copy running-config tftp
Address or name of remote host []? 10.84.0.103
Destination filename [ynt-c36-jc1a-confg]?
!!!!
13063 bytes copied in 1.956 secs (6678 bytes/sec)
YNT-C36-JC1A#copy tftp startup-config
Address or name of remote host [10.84.0.103]?
Source filename [ynt-c36-jc1a-confg]? ynt-c37-jc1b-confg
Destination filename [startup-config]?
Accessing tftp://10.84.0.103/ynt-c37-jc1b-confg...
Loading ynt-c37-jc1b-confg from 10.84.0.103 (via Ethernet0/0): !!!!
[OK - 17400 bytes]
[OK]
17400 bytes copied in 9.656 secs (1802 bytes/sec)
以上是过程，但是，重新启动路由器之后，就连接上不上了，用超级终端看到的内容如下：
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 5Mb.
Using 7 percent iomem. [5Mb/64Mb]
boot of "C3640-JS" using boot helper "flash:c3640-js-mz[1].122-23a.bin" failed
error returned: File boot failed -- File not accessible
loadprog: error - on file open
boot: cannot load "C3640-JS"
System Bootstrap, Version 11.1(20)AA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C3600 processor with 65536 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
open: file "c3745-entbase-mz[1].123-2.T6.bin" not found
open(): Open Error = -1
loadprog: error - on file open
boot: cannot load "flash:c3745-entbase-mz[1].123-2.T6.bin"
我对路由器接触不多，所以……请各位兄弟姐妹帮忙萨
问题点数：50、回复次数：5Top
1 楼oyljerry（【勇敢的心】→ ㊣提拉米苏√㊣）回复于 2005-04-02 13:03:26 得分 10
好像设置不对，还有文件找不到Top
2 楼sickeee（病孩子-还活着,真高兴）回复于 2005-04-02 20:26:10 得分 10
说明书上应该有恢复出厂设置的方法Top
3 楼bullchen（老牛）回复于 2005-04-02 20:47:34 得分 20
好像是配置有问题，重新启动吧。在启动时可以通过console串口下的打印提示操作恢复缺省的配置后再重新配置吧。
Top
4 楼Jinkan_zhong（羽习）回复于 2005-04-02 20:51:57 得分 10
UPTop
5 楼chickji（鸡仔）回复于 2005-04-04 08:41:30 得分 0
问题，已经解决了，谢谢各位。。原因是这个备份的路由器A所有配置跟B的配置完全一样了，导致，不能同时使用。改E0/0的地址Top
